Me in Stitch Magazine.

Fall 2010.

I recently had the wonderful (paid!) opportunity to write for Stitch Magazine put out by Interweave Press. I wrote out instructions for my Shadow Applique Wool Pillow for their 1 yard gifts in the Fall 2010 issue.  The magazine came out on the 14th of September so go pick it up at your nearest specialty magazine shop and try out my project!!

FREE- pattern… pleated skirt with exposed zipper and grosgrain.

sailor skirt with pocket

I call this the math skirt.  This skirt is fun and easy with sweet detail like ribbons and lace.  It can be the perfect plaid school girl skirt or if its done in denim or corduroy yer cowgirl skirt. It could be a great summer skirt in an eyelet (lined, of course) or a winter wool staple with tights.  Any way you sew it- this little equation will be sure fire PROOF!

Fabric:

1 1/4 yard of fabric

THE MATH:

Waist Measurement _____ + 40″ = __________ /2 = ___  (width)

(Example: Waist 32″ + 40″= 72″/2 = 36″).

Other Supplies:

18″ separating zip (I coordinate this with my fabric)

2 1/4 yards of 1/2″ ribbon

4 1/2 yards of 1″

waist + 4″ of wide single fold bias tape or 1″- 1 1/4″ wide grosgrain ribbon for waist facing

Zipper foot

Wash fabric, ribbon and lace if the skirt is going to be washed after it is sewn.

CUT:

Cut two rectangles that are width measurement from above x 20″ long.

STITCHING THE DARTS:

At the center point of the top edge of these rectangles, chalk a 4″ line on the back side of the fabric perpendicular to the grain line.  Measure 1″ to each side of this line and clip a notch in your fabric.  Line up your notches and stitch from notch to the end of your chalk line to create a hip dart. Press flat lining up center line with stitched line.

STITCHING THE FRONT:

Mark center front and center back on each rectangle.  Find the mid point between dart and CF and notch. Pin and stitch a 1″ deep and 9″ long pleat at this notch.  Open and press this pleat flat aligning the notch and stitching to create a box pleat.  Find the midpoint between the dart and the pleat and notch.  Repeat the steps to create the box pleat.  Find the mid point between CF and your original pleat, clip, stitch and press another pleat here.  There should be three box pleats between the side dart and the center front on each of the rectangles.

STITCHING THE BACK:

Finish both CB with either a zigzag or a serger.  Stitch center backs together (careful to line up waistlines and hemlines) with a 1/2″ seam allowance.

Measure 2″ in along waistband from the CB seam and notch.  From this notch measure another 3″ in and notch.  Continue measuring 3″ in toward the side dart until you have 5 notches.  Create a 1″ deep 9″ long box pleat using the method described above at each of the notches.  When you are finished there should be 10 pleats between the two side darts. Press all darts… again.

Note: Now is a good time to fit this garment to you.  Wrap it around yourself and adjust the fit at the center back and at the side darts if necessary.  Remember there is 1″ seam allowance at the center front.

Baste waist edge of skirt securing all pleats and darts.

ZIPPER

Fold and press 1/4″ of the center front toward the wrong side of the fabric.  Fold another 1/2″  and stitch  first fold into place finishing the raw edge.  Pin zipped zipper on top of the hemmed center front of skirt aligning the top of the zipper tapes with the waist edges and the center front hemmed edges.  Hand baste the zipper to the skirt to ensure it won’t move while machine stitching.   Unzip zipper (make sure it glides smoothly with out catching your basting.)  Here you can experiment with stitches like using a zigzag or a feather stitch while you are machine stitching the zipper into place.   Continue stitching past the end of the zipper to the hemline.  Note- there is a plastic coated section of zipper tape at the end of the zipper teeth that I some times have to hand crank my needle through.  Remove hand basting after zipper is secure.

FINISHING-

Waistline-  Stitch ribbon or bias tape on top of the waist edge at 1/2″ (wrong side of ribbon/tape to right side of skirt) leaving 1″ on each end.  Fold tape toward the back of the skirt and press this facing into place tucking in the ends of the ribbon under the facing trimming of necessary.  Stitch ribbon or bias tape to wrong side of skirt to secure the facing.

Hemline-  Finish bottom edge with a zigzag or serge.  Fold up 1″, press and stitch hem.  Stitch decorative ribbon over this hem stitching.  Using a long stitch on your sewing machine, gather the lace up enough to fit the bottom edge of the skirt. Edge stitch skirt hem on top of the gathering stitch on the lace to attach.

POCKET-

I did not use a pattern for the pocket.  I just started cutting into some scraps until I had the shape that I wanted (Yes, you can too!!)

Save a tree and make your own grocery bag- free pattern!!

Super simple!!

Super simple!!

The city of Seattle may be banning plastic bags soon.  Nancy Sewing Basket (my day job) made a little DIY PDF.  You can find it here and here.  Sorry for the two links but my boss made two PDFs so we could print (en mass) front and then back.  You can save a tree and print front, put it back in the printer (face up in my case) and then print the back.  I really want to try printing on canvas because I just got this book Printing by Hand by Lena Corwin.  Hand printed canvas would make a lovely grocery bag.  Also the new Selvedge Magazine (I heart this mag) has a great how to grocery tote.  Have lot o’ eco Fun!!